BASE PLATE: It is also called as die shoe or bolsters plate. Its main function is to provide a rigid foundation or base to the assembly. It assembles the fixed half of the tool.
Material: MS or CI.
TOP PLATE: It is the top portion of the complete tool, which holds the top assembly or complete Tool through the punch holder.
Material: MS or CI.
GUIDE PILLAR:These are cylindrical pins known as guide pins or guide pillars. These provide accurate alignment to the die set. The contacting surface of pillars and guide bushes have h7/h6 fit where as the press fitted portion of the bush with top plate have h7/j5 tolerance and are ground. One end of pillar press fitted in the base plate with h7/p6 tolerance. The other portion, which is sufficient long, provides guide for top plate for easy sliding.
Material: Case Hardened steel. IS: 17Mn1Cr95 HRC: 56-58.
GUIDE BUSH:These are mounted on the top plates, which provide smooth sliding contact between pillars and top plates.
Material: Case Hardened Steel IS: 17Mn1Cr95 HRC: 56-58
DIE: A complete tool consisting of a pair or a combination of pairs of mating members for producing work in presses. It includes well supporting and actuating part of the tool. It is a female part of a complete die.
Material: HCHCr IS: T215Cr12 HRC: 58-60
PUNCH:It is a male member of a complete dies which mates or acts in conjunction with the female die to provide a desired effect upon the material being worked.
Material: HCHCr IS: T215Cr12 HRC: 60-62
PUNCH HOLDER:It is a plate, which holds the punch.
Material: OHNS IS: T110w2Cr1
SHANK:This is a projection from the upper shoe which enters the press slide flange recess and is clamped to the slide or press ram.
Material: MS IS: ST 42
PUNCH BACK PLATE:It is a plate that supports the punch and is situated behind the punch holder plate. It avoids the dent marks that may produce during operation to the top plate.
Material: OHNS IS: T110w2Cr1
STRIPPER PLATE: It is a plate solid or movable used to strip the work piece or part from the punch. It may or may not guide the stock.
Material: MS IS: ST 42
STRIP GUIDE: In press tool the long pre-sheared stock strip to be fed through out the die surface. The strip guide combines the two metal strips or parallel blocks, which are screwed and doweled on the die surface in alignment with the die parameters. It acts as a gauge. It is one of the important elements of the progressive tools with fixed as well as floating stripper.
Material: Gauge Steel HRC: 48-50
SHEDDERS: It is used to expel the work piece from the die cavity. Shedder actuation may be achieved by
1. Pneumatic cylinder or cushion
2. Hydraulic cylinders or cushion
3. Rubber pads
4. Springs
Material: OHNS IS: T110w2Cr1 HRC: 58-60
PILOTS: Pilots are used to align the components accurately for secondary operation.
DOWELS: Dowels hold the parts in perfect related alignment by absorbing side pressure and lateral thrust.
SCREWS:The components of dies are held together by socket head cap screws or Allen screws.
Material: MS or CI.
TOP PLATE: It is the top portion of the complete tool, which holds the top assembly or complete Tool through the punch holder.
Material: MS or CI.
GUIDE PILLAR:These are cylindrical pins known as guide pins or guide pillars. These provide accurate alignment to the die set. The contacting surface of pillars and guide bushes have h7/h6 fit where as the press fitted portion of the bush with top plate have h7/j5 tolerance and are ground. One end of pillar press fitted in the base plate with h7/p6 tolerance. The other portion, which is sufficient long, provides guide for top plate for easy sliding.
Material: Case Hardened steel. IS: 17Mn1Cr95 HRC: 56-58.
GUIDE BUSH:These are mounted on the top plates, which provide smooth sliding contact between pillars and top plates.
Material: Case Hardened Steel IS: 17Mn1Cr95 HRC: 56-58
DIE: A complete tool consisting of a pair or a combination of pairs of mating members for producing work in presses. It includes well supporting and actuating part of the tool. It is a female part of a complete die.
Material: HCHCr IS: T215Cr12 HRC: 58-60
PUNCH:It is a male member of a complete dies which mates or acts in conjunction with the female die to provide a desired effect upon the material being worked.
Material: HCHCr IS: T215Cr12 HRC: 60-62
PUNCH HOLDER:It is a plate, which holds the punch.
Material: OHNS IS: T110w2Cr1
SHANK:This is a projection from the upper shoe which enters the press slide flange recess and is clamped to the slide or press ram.
Material: MS IS: ST 42
PUNCH BACK PLATE:It is a plate that supports the punch and is situated behind the punch holder plate. It avoids the dent marks that may produce during operation to the top plate.
Material: OHNS IS: T110w2Cr1
STRIPPER PLATE: It is a plate solid or movable used to strip the work piece or part from the punch. It may or may not guide the stock.
Material: MS IS: ST 42
STRIP GUIDE: In press tool the long pre-sheared stock strip to be fed through out the die surface. The strip guide combines the two metal strips or parallel blocks, which are screwed and doweled on the die surface in alignment with the die parameters. It acts as a gauge. It is one of the important elements of the progressive tools with fixed as well as floating stripper.
Material: Gauge Steel HRC: 48-50
SHEDDERS: It is used to expel the work piece from the die cavity. Shedder actuation may be achieved by
1. Pneumatic cylinder or cushion
2. Hydraulic cylinders or cushion
3. Rubber pads
4. Springs
Material: OHNS IS: T110w2Cr1 HRC: 58-60
PILOTS: Pilots are used to align the components accurately for secondary operation.
DOWELS: Dowels hold the parts in perfect related alignment by absorbing side pressure and lateral thrust.
SCREWS:The components of dies are held together by socket head cap screws or Allen screws.
Thanks for sharing this blog, this blog is very helpful information for every one.
ReplyDeletechina plastic injection molding supplier
plastic injection molding supplier